Planet ADN-4101 Router – How to Factory Reset

Planet ADN-4101 Router Reset To Factory Defaults. You can easily reset your wireless WiFi router.  Here we are also provide Reboot methods of Planet routers. You must reset your Wireless router to the factory defaults settings if you have forgotten your router user name or password. And you need to reboot your device if your router does not works properly.


This post will detail how to reset back to a factory default configuration the Planet ADN-4101. If password have been forgotten and or access to the Planet Router is limited or configurations have been done incorrectly, resetting back to the factory default settings can assist. And also provide How to change router wireless password.



Difference between Reset and Reboot :

There is a big difference between Resetting a router and Rebooting a router. Reboot means, cycle the power to Router or Refresh the router. Resetting involves changing the router settings back to its factory defaults. Perhaps you have forgotten the password of your Planet router and now you want to reset the password. First you need to Hard Reset the Router then you can use the default password to access your router.


When you reset your router the following settings will be changed:

  • Planet Router username and password
  • Wi-Fi username and password
  • ISP ip addresses and DNS
  • Any firewall settings you have made
  • Any portforwards you have set up
  • Generally, any configuration or settings changes that you have made to your router.



How To Reset Planet ADN-4101 Router With Button :

To perform a factory reset, please follow Below steps.

  • Power on the Planet Router, place a paper clip or Pin into the hole on the back of the Router labeled Reset.
  • Hold paper clip or pin down for 10 to 15 seconds and release.
  • The Router will reboot on its own. Once the WLAN light stops blinking, the Router is reset.
  • Please Note, Resetting the Planet router does not reset the firmware to an earlier version. It will only change all settings back to factory defaults.



Planet ADN-4101 Default Login, Password and IP :

Once your Planet router has been reset, it goes back to it’s factory defaults Settings.

  • IP address: or
  • Username: admin
  • Password: admin or epicrouter
  • OR see back side of your device.



How To Reset Planet ADN-4101 Router From Admin Control Panel  :

You need to know the Internal IP Address of your Planet ADN-4101 router before you can login to it. We are already placed Login details above clearly. The Planet ADN-4101 has a web interface for configuration. You can use any web browser (Firefox and Chrome) to login to the Router. First connect your router to PC with RJ45 Cat5 or Cat6 cable. Then login with above Credentials. After login follow below steps to Reset your device.


Not available


Note : If you can not get logged in to your Wireless router, here a few possible solutions you can try.

Forgot Password to Planet ADN-4101 Router :  If your Internet Service Provider or ISP supplied you with your router then you might want to try giving them a phone call and see if they either know what your Planet router’s username and password are, or maybe they can reset it for you.

How to Reset the Planet ADN-4101 Router To Default Settings : If you still can not get logged in then you are probably going to have to Hard reset your router to its default settings. Please read starting portion of this page.



How to Reboot your Planet Router :

Rebooting a router means cycling the power to it or refresh the router. If you want to reboot your router, follow below steps.

Method 1 :

  • Unplug the power connector from the back of the Planet router and plug it back in.
  • Wait above 20 seconds for the router to reboot.
  • Your internet connection may be drop when your wireless router is rebooted. If someone is using a computer on your network to access the internet, you may want to warn them.



Planet Customer Support :

If you are still having problems, contact Planet customer care department. Follow below links.


Customer Support (For Global Users)


One thought on “Planet ADN-4101 Router – How to Factory Reset

  • October 28, 2018 at 6:57 pm

    can you help me.
    i have that modem but i cannot find snr margin or line attentuation or other line statics


Leave a Reply

Your email address will not be published. Required fields are marked *